Dan's
RV7a Builder Website
Panel
| Date | Session Hours | Task |
| 6/2/2006 | 1 | misc panel adjustments |
| 6/1/2006 | 3 | finalize panel & install to cabin, test transmit |
| 5/31/2006 | 2 | more com harness work |
| 5/30/2006 | 2 | more intercom/com work |
| 5/29/2006 | 3 | remove panel & replace intercomm harness |
| 5/28/2006 | 1 | solder headphone & mic on new intercom harness |
| 5/27/2006 | 2 | reattach panel, secure throttle bracket group |
| 5/26/2006 | 2 | reattach panel and modify harnesses |
| 5/21/2006 | 5 | build gps harness, hotwire to panel, mount antenna to fwd dash panel |
| 5/18/2006 | 1 | cut panel hole for the gps airmap2000c |
| 5/17/2006 | 2 | pull panel, mount transponder tray |
| 4/11/2006 | 1 | reset panel & reconnect wiring |
| 11/18/2005 | 1 | drill panel for red panic light for EIS |
| 11/16/2005 | 1 | install EIS 4000 module to panel |
| 11/13/2005 | 1.5 | attach comm wiring harness to intercom & load to panel, prep for panel to cabin install & test |
| 11/12/2005 | 3.5 | complete comm harness & integrate into intercom |
| 11/11/2005 | 5 | build comm harness, prep cabin ribs for comm cable to antenna, fix radio stack for comm |
| 11/10/2005 | 2 | finish building & attach radio stack bracket, remove panel for comm attachment |
| 11/8/2005 | 3 | cutout rear secondary panel for comm radio installation |
| 6/21/2005 | 1 | misc panel, prep & paint panel finish screws… |
| 6/3/2005 | 1 | more panel wiring stuff |
| 6/2/2005 | 1 | grind panel & attach flap panel switch |
| 6/1/2005 | 1 | wire wrapping of intercom harness |
| 5/31/2005 | 1.5 | wire wrapping & wiring behind panel |
| 5/30/2005 | 2.5 | wire intercom & solder plug connections |
| 5/1/2005 | 2 | fabricate remote compass bracket & preliminary intall on F707 bulkhead |
| 4/27/2005 | 1 | mount dynon efis |
| 3/21/2005 | 1.5 | complete db sub solder connections on the intercom assy |
| 3/20/2005 | 2.5 | build intercom & power outlet wiring harnesses |
| 1/29/2005 | 3 | mount power outlets, exp2 bus to support bracket & indicator guage, headphone,mic& stereo toggle switch to panel |
| 1/27/2005 | 2.5 | final coat on panel, wrinkle paint map box, begin setup of panel items |
| 1/26/2005 | 1 | 3 coats of wrinkle paint on the instrument panel |
| 1/25/2005 | 1.5 | cut elt & intercom mounting holes in panel, sand & primer. |
| 1/18/2005 | 0.5 | sand down & rework panel surface, test paint wrinkle paint |
| 1/17/2005 | 2 | redo map box door & rivet to panel, locate & drill additional hole for stereo jack input |
| 1/9/2005 | 2 | completed cutting panel |
| 1/1/2005 | 2 | mapbox prep, locate & cut panel for headphones, mic & power plugs |
| 12/30/2004 | 1 | mapbox prep |
| 12/29/2004 | 1 | mapbox prep |
| 12/26/2004 | 1 | continue with panel |
| 12/24/2004 | 2 | panel cutouts |
| 12/23/2004 | 1 | begin panel cutouts |
| 12/6/2004 | 1 | Layup work |
| 12/4/2004 | 1 | map box drill, countersink & rivet |
| 12/1/2004 | 1 | map box drill, debur.. |
| 11/30/2004 | 1 | begin panel layout, cut map box hole |